No products in the cart.
04 3550600
052 7036860
Print Servers
HP Jetdirect 600N EIO Internal Print Servers
Availability:
10 in stock
د.إ699.00
10 in stock
The HP Jetdirect 600N (EIO Internal Print Server) provides a network connection for the new HP peripherals equipped with an enhanced I/O (EIO) interface slot. The HP Jetdirect 600N EIO cards have 2 MB of upgradeable Flash memory and perform at two times the speed of MIO HP Jetdirect cards.
Model numbers
J3110A, J3111A, J3112A, J3113A
Configurations and models
| Configurations | Model Number |
|---|---|
| HP Jetdirect 600N EIO Internal Print Server for Ethernet/10Base-T networks | J3110A |
| HP Jetdirect 600N EIO Internal Print Server for Ethernet/10Base-T and 10Base2 and LocalTalk networks | J3111A |
| HP Jetdirect 600N EIO Internal Printer Server for Token Ring networks | J3112A |
| HP Jetdirect 600N EIO Internal Print Server for Ethernet/10/100Base-TX networks | J3113A |
Product overview
Supported protocols
| Supported Network Protocols | Supported Networks | 600N Product Model | |||
|---|---|---|---|---|---|
| IPX/SPX | Novell IntranetWare Novell NetWare | J3110A J3111A J3112A J3113A | |||
| IPX/SPX-compatible | Microsoft (R) Windows 95 Microsoft Windows NT | J3110A J3111A J3112A J3113A | |||
| EtherTalk | AppleTalk | J3110A J3111A J3113A | |||
| LocalTalk | AppleTalk | J3111A | |||
| DLC/LLC | IBM LAN Server Microsoft LAN Manager Microsoft Windows for Workgroups Microsoft Windows NT Artisoft LANtastic* | J3110A J3111A J3112A J3113A | |||
| TCP/IP | Windows XP, 2000, NT lpd UNIX (R), including: Hewlett-Packard HP-UX, Sun Microsystems SunOS/Solaris (Sun SPARCsystems only), SCO UNIX**, IBM AIX**, HP MPE-iX**
Windows 95, 98, Me |
J3110A J3111A J3112A J3113A |
Electrical characteristics
1.25 A maximum at 3.3 V nominal
Environmental operating conditions
| Operating | Non-Operating | |
|---|---|---|
| Temperature | 0 to 55 degrees C (32 to 131 degrees F) | -40 to 70 degrees C (-40 to 158 degrees F) |
| Relative Humidity (non-condensing) | 15 to 95% at 40 degrees C (104 degrees F) | 15 to 90 percent at 65 degrees C (149 degrees F) |
| Maximum Altitude | 4.6 km (15,000 feet) | 4.6 km (15,000 feet) |
Port configuration
| Model | Port Configuration |
|---|---|
| J3110A | Ethernet, IEEE 802.3 Type 10Base-T (RJ-45) |
| J3111A | Ethernet, IEEE 802.3 Type 10Base-T (RJ-45), Type 10Base2 (BNC), and LocalTalk (Mini-DIN 8) |
| J3112A | Token Ring/IEEE 802.5 (RJ-45 or DB-9) |
| J3113A | Fast Ethernet, IEEE 802.3 Type 10Base-T or IEEE 802.3u Type 100Base-TX (RJ-45) |
Product bundles
One HP Jetdirect card with one HP Jetadmin CD.
Recommended cables and requirements
| Model | Port Configuration |
|---|---|
| J3110A | 10Base-T unshielded twisted pair cabling |
| J3111A | 10Base-T unshielded twisted pair cabling, 10Base2 thin coaxial cabling, or 8-pin mini-DIN (LocalTalk) |
| J3112A | Type 1, 2, or 6 shielded cabling (Token Ring) or shielded and unshielded twisted pair cabling (RJ-45) |
| J3113A | 10/100Base-TX unshielded twisted pair cabling |
Setting the jumpers on the J3113A to 10/100 link speed
Link configuration jumpers (P1, P2, and P3) can be used to configure the print server. These jumpers should be used if the print server is unable to establish a network link through autonegotiation. If P1 is changed to the AUTO=OFF position, then P2 selects the link speed (10 or 100 Mbps) and P3 selects the communication mode (Half duplex or Full duplex). If you manually configure the print server using jumpers P2 and P3, you must match the configuration of the connecting device, such as the network hub or switch.
Figure 2: Jumper Locations and Labels
1Â -Â 1- This Jumper is Labeled Auto
2Â -Â 2- This Jumper is Labeled 100
3Â -Â 3- This Jumper is Labeled H
In the table below, the “0” ‘s mark the position of the exposed pins and the “X” ‘s mark the position of the jumpers, one jumper over two pins.
| Setting | Label | P1 | Label | P2 | Label | P3 |
|---|---|---|---|---|---|---|
| AUTO=ON (Default)* | Auto | X X O | 100 | X X O | H | X X O |
| 100 Mbps Half-Duplex (AUTO=OFF) | Auto | O X X | 100 | X X O | H | X X O |
| 100 Mbps Full-Duplex (AUTO=OFF) | Auto | O X X | 100 | X X O | H | O X X |
| 10 Mbps Half-Duplex (AUTO=OFF) | Auto | O X X | 100 | O X X | H | X X O |
| 10 Mbps Full-Duplex (AUTO=OFF) | Auto | O X X | 100 | O X X | H | O X X |
Manual part numbers
| Product | Language | Part Number |
|---|---|---|
| HP Jetdirect Interface Manual Kit | English | 5063-2111 |
| HP Jetdirect Hardware Installation Guide | 5967-0854 | |
| HP Jetdirect Software Installation Guide | 5966-5171 | |
| HP Jetdirect CD-ROM Installation Booklet | English French Italian German Spanish | 5966-5248 |
| HP CD-ROM Installation Booklet | Chinese Korean Japanese Simplified Chinese | 5967-0823 |
| Data Sheet | 5966-0084E | |
| HP Jetdirect Connectivity Guide | 5966-0083E |
Pre-installed software
No pre-installed software; each card comes bundled with HP Jetadmin software on CD.
Warranty
-
One-year return to HP
-
Standard Delivery Unit Exchange
Energy Star compliance
None
Regulatory compliance
-
FCC Class A for HP J3112A Token Ring, and for HP J3110A/J3111A/J3113A Ethernet or IEEE 802.3/802.3u
-
FCC Class B for HP J3111A with LocalTalk Only
There are no reviews yet.