Ashly nXp3.02 2-Channel Network Power Amplifier

Selectable at 26 dB, 32 dB, 38 dB, or 1.4 V

>250 (8 Ω load <1 kHz)

Input High Pass Filter: 80 Hz 2nd order

<0.5% SMPTE, typical
<0.5% THD-N, typical (8 Ω, 10 dB below rated power, 20 Hz to 20 kHz)

-75 dB (dB from full output, 1 kHz)

20 Hz to 20 kHz, un-weighted
>114 dB (all 3.0x models)

20 Hz to 20 kHz, ±0.05 dB

Balanced Input Connector: Euroblock 3.5 mm, 1/4″ TRS, and XLR combo jack

10 kOhms

+21 dBu

Connector: Neutrik & speakON

Control Network: Compatible with standard 100 MB Ethernet

Connector: Balanced Euroblock 3.5 mm
Maximum Output: 21 dBu

Remote Standby: Euroblock 3.5 mm, close contact to GND for standby mode
Preset Recall: Euroblock 3.5 mm, close contact to GND for preset 1-4 recall

Data Connection: Euroblock 3.5 mm – Gnd, +18 V, In, Out

Remote DC: Euroblock 3.5 mm – Gnd, CV, V+ per input

Front panel, software, offset link group, and remote per channel
fully off = mute

Amplifier Protection: Inrush current limitation, temperature monitoring, output over-power protection, mains fuses

Continuously variable temperature controlled axial fan(s)

Non-condensing 32 to 113ºF (0 to 45ºC)

At 50 Hz
Nominal (Automatic Sensing SMPS): 120 VAC
Operating Range: 70 to 135 VAC
Minimum Power-Up: 85 VAC

At 60 Hz
Nominal (Automatic Sensing SMPS): 240 VAC
Operating Range: 140 to 270 VAC
Minimum Power-Up: 170 VAC

Power Cable Connector: 20 A powerCON

For Max Output Power Per Channel, EIAJ Test Standard, 1 kHz, 20 Hz to 20 kHz, 1% THD & Low Z Output: 2 Ω: 3000 W
4 Ω: 2000 W
8 Ω: 1250 W

For Low Z output, Bridge Mode, 20 Hz to 20 kHz & 1% THD:
4 Ω: 6000 W

For Output Per Channel:
70 V: 2450 W
100 V: 1250 W
Note: All Channels Driven

Sleep Mode: < 1 W
Standby Mode: 40 W
Idle (No Signal): 55 W
Note: All Channels Driven

For 120 VAC
Sleep Mode: 0.1 A
Standby Mode: 0.70 A
Idle (No Signal): 1.00 A

For 240 VAC
Sleep Mode: 0.05 A
Standby Mode: 0.35 A
Idle (No Signal): 0.5 A
Maximum for all Channels Driven:
For 120 VAC
Typical: 14.7 A
For 240 VAC
Typical: 7.3 A

Thermal Dissipation: Sleep Mode: <3.4 BTU/hr
Standby Mode: 136 BTU/hr
Idle (no signal): 187 BTU/hr
Typical (1 / 8 Max Power): 1,360 BTU/hr
Note: All Channels Driven

Front Panel LED Indicators: White LED:
Power Switch: On, off, standby (flashing)

Red LED:
Clip / Mute Per Channel: Clip @ 1 dB below full output / mute
Protect: On, Off

Green LED:
Signal Per Channel: -18 dBu
Bridge Per Channel Pair: On, off
Com: On, for Ethernet data or device ID
Current Per Channel: Proportional to output

Yellow LED:
Temperature Per Channel: On dim at 90% max operating temperature, full bright + protect at 100%
Sleep: On, amplifier is asleep from audio inactivity
Disable: On, power switch & front panel attenuators are disabled

Protēa DSP
Options: Analog, auto (net, AES3, analog) Note: All DSP functions can be linked to 1 of 16 link groups

Brick Wall Limiter: Threshold: -20 to 20 dBu
Ratio: Infinite
Attack: 0.2 to 50 ms/dB
Release: 5 to 1000 ms/dB

Advanced Gate Controls: Key Engage Enable: Yes
Key Frequency: 20 Hz to 20 kHz
Key Bandwidth: 0.016 to 3.995 octave

Gain (with / without VCA): -50 to 12 dB, off, polarity invert
Digital VCA Groups: 4 available
Remote RD8C Gain: Enable per channel, 0 dB to -∞
WR-5 (neWR-5) Remote Gain: 0 to -50 dB, mute

For 31-Band
Filter Type: Constant Q or proportional
Bandwidth: 0.499 octave to 0.25 octave

For Parametric 2,4,6, or 10 Band
Frequency: 20 to 20 kHz
Level: -30 to 15 dB
Q Value: 0.016 to 3.995 octave
For Hi / Low Shelf 6 / 12 dB/octave
Frequency: 20 Hz to 20 kHz
Level: -15 to 15 dB

For All Pass
Frequency: 20 Hz to 20 kHz

For Variable Q HP / LP
Frequency: 20 Hz to 20 kHz
Q Value: 3.047 to 0.267

For Notch / Bandpass
Frequency: 20 Hz to 20 kHz
Q Value: 92.436 to 0.267

2 Way, 3 Way, 4 Way Crossover & High Pass / Low Pass Filters
Bessel & Butterworth Filters: 12 / 18 / 24 / 48 dB/octave
Linkwitz-Riley Filter: 12 / 24 / 48 dB / octave
Frequency: Off, 20 Hz to 20 kHz

Sampling Rate: At 48kHz (Input Time, Distance & Temperature)
Speaker Delay: 0 to 21 ms
Delay: 0 to 682 ms At 96 kHz (Input Time, Distance & Temperature)
Speaker Delay: 0 to 10.6 ms
Delay: 0 to 341 ms

Range: -60 to 20 dBu
Increments: 1 dB
Peak Hold Indicator: Yes

Pink Noise, White Noise, Sine Wave
Signal Level: Off, -50 to 20 dBu
Sine Wave Frequency: 20 Hz to12 kHz

Input A/D, Output D/A: 24 bit
DSP Processors: 32-bit floating point
Sample Rates: 48 kHz, 96 kHz
Propagation Delay @ 48 kHz: 1.42 ms
Propagation Delay @ 96 kHz: 0.71 ms

Gain (0.5 dB Increments): Off, -50 to 12dB
Mute: Per channel
Auto-mixer Enabled: Per channel
Global Auto-mixer Response: 0.01 to 2 sec
Enable Ducking at Mixer: Yes
Ducking LED: Per channel if enabled Metering: Level, auto-mixer level

Number: 12 In/Out per filter: Yes
Lock per filter and global lock: Yes
Filter Modes: Float, Restricted, Manual
Filter Type: Notch, Parametric
Filter Frequency Range: 20 Hz to 20 kHz
Notch Filter: -∞
Parametric Filter: 15 dB to -30 dB
Filter Bandwidth: 0.016 to 3.995 octave
Detector Sensitivity: 5 levels
Float Time: 5 minutes to 24 hours

-20 to 20 dBu

1.2:1 to infinite

0.2 to 50 ms

5 to 1000 ms/dB

Peak / average

2 available

In, out, attenuation, graphical

Target Level: -40 to 20 dBu

Gentle, normal, aggressive, user defined

0 to 22 dB

Input, gain, attenuation

1.2:1 to 10:1

-30 to 0 dB

5 to 1000 ms/dB

0 to 6 sec

Maximum: -20 to 20 dB
Minimum Base: -40 to 20 dB

0.2 to 20 s/dB

Link Groups: 16 available

ANC: 1 to 2 or 1 to 4

Noise: -40 to 20 dBu

Program/Ambient Gain: 0.3:1 to 3:1

Input level, attenuation, average noise

Trigger Threshold: -80 to 20 dBu
Ducking Release: 5 to 1000 ms/dB
Ducking Depth: 0 to -30 dB, -∞
Enable Ducking at Matrix Mixer: Yes
Metering: Input

-80 to 20 dBu

Off, 100 to 0 dB

0.2 to 50 ms/dB

5 to 1000 ms/dB

Key signal, gate LED, graphical

19.0 x 3.5 x 16.8″ (482.6 x 89.0 x 426.7 mm)

< 28.0 lb (12.7 kg)

32 lb

19 x 16 x 4″